Bally 809 Slot Machine Manual

admin

Bally E-809, E-831, E-873 Illustrated Parts Catalog. Approx 19 page print Comb bound with Cardstock Cover. This manual is written for Location management and Service Technicians. This is part of an extensive lot of slot manuals that i will be listing for a Las Vegas Slot Tech. If you're looking for a slot machine manual we probably have it. Buy Sell Trade & Repair Slot Machines and Casino Gaming Equipment and Tables 763-253-0230 info@worldwide-gaming.com. 809 Multiplier was produced by Bally Manufacturing Co. Bally Manufacturing Co. Released 868 different machines in our database under this trade name, starting in 1930. Other machines made by Bally Manufacturing Co. During the time period 809 Multiplier was produced include 42nd and Broadway, Wall Street, Reward Time, Bamboo, and Single Coin. Bally Model #809 Slot Machine. But I have an owners manual with a maintenance schedule in it. Recently my nephews got a hold of the keys. A quick look round a typical Bally electro mechanical reel mechanism, from a slot machine (fruit machine in the UK). Showing the win combination circuitry a.

INFORMATION FOR VIEWING AND DOWNLOADING

To download, right-click on link and 'Save Target As...'

Bally Bingo Green Book -- Parts List and Exploded Diagrams of components.

Introduction to Bally Flipper Games.

Bally Broadway Bingo Pinball Operating Instructions. A schematic is available but must be commercially reproduced.

Pace Slot Machine Award Cards, Hi-Res Scan.

Autobell Circus Schematic.

Bally Sportsman Flasher Slot Machine operating instructions, pay tables, etc. A schematic of the machine is available on request.

For Amusement Only sign furnished with Bally bingo pinball machines. Print on cardstock and put one on your machine.

Mills Bell Machine Parts and Service Manual HiTop 7-7-7 Model.

PAR sheet for Fourth of July.

Example of a Bally Bally SMI Sheet (PAR Sheet) in PDF format.

PAR Sheet possibly for a Double Bucks machine in PDF format.

Coin Mechanisms, Inc. See National Slug Rejectors and Coinco below.

Bally V-1088 and V-1090 Operator Instructions Manual.

Bally V-1297 Instructions and Bally V1297 Parts.

Bally Double Progrressive Operator Instructions using version 6 for use with Series 1000, E-2000, V-2000, S-5000 and V-5000.

Bally Deluxe Draw Bell Instructions and Award Cards. The award cards provided different values for the Special and Super Special for both Replay and Automatic Payout operation. Operators could tailor the payouts to the location. These cards are scanned at 300 dpi for quality reproduction. For other similar Bally machines, these cards can provide a guideline. Edit them with a photoshop-type program.

Two Mills catalogs from the early 1900's: The Mills Commercial trade stimulator and Mills Amusement, Skill & Vending Machines.

Keeney's Super Bell Operators Manual in PDF format. 1941 document.

Keeney's Bonus Super Bell Instruction Manual. This is a copy of a manuscript and is not the final manual, however it may assist you to understand the operation of the machine.

Mills Vest Pocket Slot Machine Operators Manual, 16 pages in PDF format.

Evans Consoles This is the 1941 Instructions and Parts Catalog for Galloping Dominos, Pacer, Bang Tails and Lucky Star. Much of this information can be applied to machines into the late 40's. The wiring diagram shows how it is laced together. This document is in PDF format. Adobe's free Acrobat Reader may be obtained Here.

Evans Winterbook Parts Manual in PDF format.

An Introduction to Bally Slot Machines, Manual 6000 1979. This is a good primer for Bally electro-mechanical slot machines. Page 22 corrects the myth of how the slot machine got its name--it certainly wasn't what I thought. This manual, in PDF format, is 45 pages in length and it is broken down into five parts for easier downloading. Adobe's free Acrobat Reader may be obtained Here.

National Slug Rejector and Coinco Service Manuals in .PDF format for some older equipment. Coin acceptors normally operate transparently, but they can surely be a nuisance when needing service or adjustment.

Mills Story and Catalog, Late '40s, an issue of Spinning Reels, has a brief history of Mills Novelty Co. with descriptions and depictions of then current Mills products. Ancillary equipment is described such as jack-in-the-box safes, regular safes, coin changers, coin counters and a bell machine tool set. In its day, the tool set cost about as much as a bell machine.

Jennings Chief Parts and Service Manual in PDF format. The scanned doucment was a poor copy so this is possibly just better than no manual at all.

Bally Slot Consoles parts list and description including Triple Bell and Deluxe Draw Bell. This includes pictorials of the reel assembly. A schematic for the Triple Bell is available from Internet Direct.

Bally Reflex Unit With Snap Switches used in Champion games through Serial No. 9053. They were not used in the companion game, Kentucky.

Buckley Track Odds 1938 Machine description, troubleshooting, partsand diagrams. About 80 pages. The file number = page number.

Buckley Track Odds Circuit Tracing Guide for machines 12,000-12,500.

***Some electrical drawings are available for the Buckley Track Odds machines on request. They must be commercially reproduced.

Buckley Track Odds Remote Control installation instructions.

Bally Electro-Mechanical Slot Machine Manual. Covers Money Honey up to the 'computers' took over. The file numbers = page numbers in the manual.

Need more than a manual? Bally Electro-lMechanical Video Guide is available at nominal costs.Bally Electro-Mechanical Troubleshooting Reference. File 0000 is the index.

Limited Bally Coil Reference in a zip file for quick download.

The Last of the Bingo Kings -- Not exactly the Sopranos.

Bally Victory Special Setup Instructions showing some adjustments available to the operator.

Be sure to check the Links page for additional resources.

Pace Slotmachine Manual. Print sheets 1 to 10, turn paper over and print sheets 11 to 20. Fold to make booklet.

Bally Citation and Lexington One Balls A schematic is also available, but too large to scan. Documents for Bally Trophy, Jockey Club, Turf King, Grandstand and Futurity are available on request.

Directions for Operating Mills Operator's Bell COK and FOK Mint Vender.

Bally Triple Draw Bell adjustments. Schematic and Relay/Switch chartsare available from Internet Direct Also available from Internet Direct are documents forBally Triple Bell, Bally Spot Bell, Bally Turf King and Kentucky.

Williams: An Introduction To Coin Operated Amusement Games This document is long --66 pages in .PDF format. Amusement machine components are discussed however many aspects apply to gambling machines. Schematics are explained. There is a lexicon of coin machine terms. Adobe's free Acrobat Reader may be obtained Here.

Metal Forms Products Company I have not seen this company referenced anywhere on the WWW, however they manufacture hard to find mechanical slot parts for Mills, Jennings, Caille, Watling, etc. Their inventory includes vendors, springs, reel tins, discs, disc plugs, cash boxes, back doors, decals and back door paper for restoration. If you have been looking for a hard-to-find part to get your project working, you may find it here. The file number = catalog page.

Mike Munves catalogstill missing 4 pages. Here is a look back in history to 1956 and the machines available. All these games were before video games. The pricing is interesting. Keep in mind that a very good job in 1956 paid $500 monthly. There are 6 files in PDF format to facilitate downloading. Adobe's free Acrobat Reader may be obtained Here.

This is a 16-page Mike Munves 1940 Catalog. The catalog was scanned from a b/w xerox copy of original (or perhaps another copy) and does not have very good detail. It does give a feel for what was then available. This file is in PDF format.

This Ray Oakes & Sons Amusement Trade Catalog from 1960 is of interest to our outdoor amusement friends. I do not believe that they are in business any longer.

Keeney Big Tent Manual. This is a flasher slot. I have the schematics but they are too large for my scanner. I can have them reproduced on request.

K. C. CARD CO CATALOG, 1960. This catalog is a textbook all its own in controlled gambling equipment. An 8-page supplement added near the middle of the catalog offered devices manufactured by H C Evans Co or their successors. The original H C Evans Co was liquidated in 1956 following the death of its owner. PDF format. Adobe's free Acrobat Reader may be obtained Here.

Tax Matters.The operators were not without their hassles. From my experience with bingos, it is hard to believe the payoff percentages of the machines discussed. This document is in PDF format. Adobe's free Acrobat Reader may be obtained Here.

H C Evans Co Catalog. For those who have never seen a copy, this catalog is a tell-all of controlled gambling and carnival equipment. If you ever thought that you were fleeced at a gambling game, you may find the answer here.

Evans Club, Park and Carnival Equipment with 1961 price list. This catalog was issued by the Evans Park & Carnival Device Corporation, successors to H. C. Evans & Co. I do not believe any catalogs of Evans equipment were published after this one. I do not know how long the company remained in business after 1961.

More for our outdoor amusement friends -- A collection of Wurlitzer Band Organ Music.

Games, Inc WILDCAT Service Instructions and Parts Catalog in a 10-page .PDF format document. Adobe's free Acrobat Reader may be obtained Here.

H C Evans 1909-1910 Catalog. This Evans catalog includes pages advertising sporting goods such as baseball gloves, firearms (a shotgun for $5) and fishing rods, reels and tackle.

Bally Series E Link Progressive System Operators Manual.

Mills Automatic Money Makers, a catalog of early Mills machines.

Caille Brothers Catalog of early slot machines and trade stimulators.

Mills Trade Stimulators catalog, early 20th century.

PEPLUS video poker machine info.

Program Summary Reports examples for some S Plus machines.

IGT Program Index.

Williams Upright Video Slot information.

Pot Of Gold manual.

Repair Tips for Reel Readers

How to test and what to look for when doing your own repairs

When one of these goes bad you may see an error that would be 4x or 7x where x indicates thereel position, i.e. a 43 error code would indicate the reel reader on the third reel.

What is described below is for testing the reel reader card using this home built tester. The tester provides both a 50 volt source or a 5 volt source (switch selectable).

After describing this procedure I will tell you how to test the cards with out having to have a 50 volt source.

I designed and built a tester to make troubleshooting easier. I test the card and all of the photo-transistors
first, then I split the two halves of the card, one for cleaning but also so that I can use a dental tool, poking
it into the tiny opening to push the photo-transistor or IR Emitter back up and out of the small square opening. The photo-transistor/Emitter should be at something close to a 45 degree angle.

Once the bad components are pushed out of the way, I use my soldering iron to melt the solder on both leads at the same time while grasping the upper portion of the optic. It comes off very easily. Once removed use solder wick to remove the excess solder. You want to do this so that when you put in the new device the leads will be nearly flat on the PC board.

Replace the defective components and quickly tack one side, allow the solder to cool and then solder the other side. Once the other side has cooled you can go back and firmly solder the lead that was previously tacked. Reassemble and then retest to make sure that the optics are working properly. Tapping the top of the card lightly with the handle of a screw driver will show any intermittent connections.

The one question that may come up is what constitutes a bad device. Since the reader cards supply signals to TTL logic devices then we can use standard logic levels of 2.0 volts as a high and .8 volts as a low. When measuring the output of the photo transistor, if the voltage is less than 2.0 volts, while unblocked or higher than 0.8 volts when blocked then that photo-transistor (or emitter) is defective.

In the cards that I have repaired I typically see voltages of greater than 4 volts unblocked and .01 volts blocked for the 50 volt reader cards, 5 volt reader cards the unblocked voltage is 3.14 and the blocked voltage 0.2.
Test all of the emitters and photo-transistors first, the replace all defective ones. I make it a habit to clean the bulbs with alcohol on the 50 volt cards so that as much light as possible gets to the photo-transistor.

Testing reel readers without having a 50 volt source.

The 50 volt supply is only used to power the incandescent bulbs. They are in series along with the 470 ohm resistor. Each bulb requires 5 volts to operate properly.

You need a few basic items, a Volt/Ohm meter (DVM) , a 47K resistor, a light source (flashlight) and some clip leads and a 5 volt DC power supply

Split the cards by removing the 2 screws and lay the small card off to the side

If you lay the card flat on its back with the mounting bracket to the left then the pins at the bottom will number 1 through 16 from right to left
Measure the resistance between pin 16 and 14, Pin 16 is Vcc and 14 is Ground you should have a reading a bit above 500 ohms, indicating that the 470 ohm 2 W resistor and all of the bulbs are OK. If not in this range then you will have to remove the tape covering the backs of the bulbs and then measure resistance across each bulb individually. Remember the bulbs are wired in series like the old Christmas tree light strings.

Assuming that the bulbs and resistor are OK. Attach the ground lead of the volt meter and one end of the resistor to pin 14 (pairs 13/14)
of the card. Connect the other end of the resistor and the positive lead of the volt meter to pin 11.

Now using the 5 volt supply, apply 5 volts to pin 1 of the card and read the voltage, shine the light into the small (tiny) hole that is for Q1, voltage should be some where around 4.7 volts with the light on and some where less than 0.2 volts with the light off. Just keep in mind that ambient light might cause the light off reading to be higher. The acceptable voltage ranges need to be within the acceptable ranges used in ‘Logic” circuits so a logic high you need 2 volts or more and a logic low 0.8 volts or less.

You may find that if you have these readings, a Q-tip dipped into alcohol can be used to clean the top of the photo-transistor by pushing the Q-tip into the hole and then twisting the Q-tip. I routinely clean these as well as to clean the bulbs.

Repeat this process for each of the following pins 1, 3, 5, 7, 9

Other than pin 11, all of the other pins are in pairs

Pins 1 & 2 Collector of Q1
Pins 3 & 4 Collector of Q2
Pins 5 & 6 Collector of Q3
Pins 7 & 8 Collector of Q4
Pins 9 & 10 Collector of Q5

Pin 11, Common emitter
Pin 12 Missing (pin is cut off)

Pins 13 & 14 Ground
Pins 15 & 16 Vcc
This process is not nearly as quick or accurate as using the tester but should allow you to test each of the cards.

The 5 volt card testing process is not much different other than it is not necessary to split the cards and you need a 3K resistor instead of a 47K resistor.

Apply the 5 volts across pins 16 and 14 and then measure the voltage on the associated
pin pairs.
In this case the 3K resistor attached to pin 14 and pin 11 biases another transistor’s base (Q6), pulling it low so that it will turn on the IR Emitters. Remember to block the light for each IR emitter to see the photo-transistor transition to a low state.

Testing results for the 5 volt cards readers you will not read anywhere near 4.7 volts, they will be closer 3.0 volts for a high and about 0.2 volts for a low

Repair Tips for Power Supply

I have noticed that the schematic for the Bally E1000/E2000 power supplies list expected voltages, but, what does that mean?

I have a couple of these power supplies so I decided to do some testing to see what voltages were obtained under certain circumstances.

If you apply 12 VAC across pins 1 and 10 of the board J1 connector,you should be able to measure the voltages on the test points (+UR, ZC and 5V)

These voltage readings are based on a supply that has no load (nothing else connected)

UR = 15.96 VDC
ZC = 10.07 VDC
5v = 5.0 4VDC


One might think something is wrong because both UR and ZC are higher than the schematic states. However with no current we would expect to find the voltages higher, what matters is the voltage under load conditions.

The LM340-T5 Regulator has a maximum current output of 1 amp so using ohms law we know the voltage is 5 volts and the current is 1 Amp, Resistance can be calculated using the formula R=V/I (R=5/1) so R=5Ω, Now that we know what to use, we can figure out the wattage, this is rather simple, Watts = Amps x Volts so in this case we have 5 volts, 1 Amp so need 5 Watts. For testing I use a couple of 5Ω 5W resistors , actually, I use 20 Watt resistors to keep from burning my fingers. Anything smaller than 5W will burn and smoke is bad. The load resistors are placed across pins 13 and 20 of the J1 connector

To test the power supply drawing .5 amps we place 2, 5Ω resistors in series for a total of 10 Ω. With a 10 Ω load, drawing .5 amps these readings are fairly typical of what you should expect to see

UR = 12.16 VDC
ZC= 8.83 VDC
5v = 5.01 VDC

The final test is to test at full load, drawing 1 amp of current by removing one of the 5 ohm resistors so that only 5 ohms appears across pins 13 and 20 of J1, the readings you should expect to see would be.

UR = 7.57 VDC
ZC= 9.6 VDC
5v = 4.98 VDC

It would appear that the voltages shown on the schematic are voltages when the power
supply is measured with a full load.

I also recommend that when repairing these power supplies to remove the heat sinks from the bridge rectifier (BR1) and the 5 volt regulator (Q1). Clean off the old thermal heat sink compound and add new compound so that the heat transfer is more even. This will allow for maximum cooling.

The minimum voltage to expect from the LM340-T5 is 4.75 volts, if less than this then it is better to spend a couple of dollars and replace it.

Sometimes you will find that you have no voltage. In this case you want to check the 4 diodes and if the voltage seems to be half of what you expect then check the solder connections on the bottom side of the diodes. These will become bad because of heat. Other causes of no voltage is an open diode in the Bridge Rectifier (BR1).

Bally 809 Slot Machine Manual Download

I would recommend to anyone doing any type of repair work to invest in an ESR Meter. ESR means Equivalent Series Resistance and a high ESR can have adverse actions to your circuit. I have had several of these power supplies where despite changing the diodes, bridge rectifier and voltage regulator the output voltage was still below the regulators specified voltage of 4.75 volts @1 amp. These problems were resolved using my ESR meter and the discovery of the large 11,000 ufd capacitor having a high ESR value.

Can’t run Tests

Machine

I have seen many complaints of not being able to run the tests or clear errors on these E Series machines. If you have a light tower the WHITE light should be illuminated before the tests or resets can be done. This does not mean that a burnt out bulb will prevent this but only serves as a quick indication that you should be able to run tests or clear error codes. If you find that you are unable to run the tests or reset the machine, check the cherry switch behind the door hinges. If this switch goes bad it will signal the MPU board that the door is closed. Many owners of these E machines will bypass the door switch however the cherry switch must be operational

Bally 809 Slot Machine Manual

RAM Tester

Bally 809 Slot Machine Manual Troubleshooting

Since many of the problems with the E Series slot machine are related to RAM failures I thought it would be a good idea to have one hanging around in my shop. I searched the web and located a guy that had developed a tester for testing the 6264 RAM chips. I sent him an email asking if this might be easily converted to test the 5101 RAM chip used in the Bally E Series slot machines and a large number of Bally Pinball machines. As it turned out he did not have a problem in making this modification as an ‘Engineering Change’ for me. My tester only tests the 5101 RAM chips, but NeoLoch Sales has since altered the design so that it will now test 5101, 6116, 21C14 and 9114 RAM Chips. It also will run on a 5, 12 volt power supplies or from a 9 volt battery.

Bally 809 Slot Machine Manuals

For further information please visit his website NeoLoc the page will open in a new window. This tester is now obsolete and has been replaced by a newer more versatile version

Bally 809 Slot Machine Manual Machine

If you have some electronic design work that you need to get done contact David, he is easy to work with and offers reasonable prices.